1. You are viewing our forum as a guest. For full access please Register. WindowsBBS.com is completely free, paid for by advertisers and donations.

Modems and XP networks

Discussion in 'Networking (Hardware & Software)' started by Omega, 2004/07/20.

Thread Status:
Not open for further replies.
  1. 2004/07/20
    Omega

    Omega Inactive Thread Starter

    Joined:
    2004/03/11
    Messages:
    46
    Likes Received:
    0
    Could someone tell me if it is possible to network 2 XP systems that each have there own modems??

    I have no problem networking these systems but When I run the wizard it wants to allow only the use of one modem for both computers. What I'd like it to do is each computer to use its own modem.
     
  2. 2004/07/20
    24jedi Lifetime Subscription

    24jedi Well-Known Member

    Joined:
    2002/06/19
    Messages:
    186
    Likes Received:
    0
    How are they networked ?
    What is the purpose of the modems ?

    If the computers are in the same room (or house), you can network them simply by using the network cards and a hub/switch. No modem required. As an alternative, you could use a crossover cable directly in each network card.
     

  3. to hide this advert.

  4. 2004/07/20
    Omega

    Omega Inactive Thread Starter

    Joined:
    2004/03/11
    Messages:
    46
    Likes Received:
    0
    Right now thr computers are not networked.

    Each computer has its own modem for separate internet access.

    Simply put I want to connect them by LAN but to not share internet access.
    I want them to use there own modems.
     
  5. 2004/07/21
    PeteC

    PeteC SuperGeek Staff

    Joined:
    2002/05/10
    Messages:
    28,896
    Likes Received:
    389
    Quite possible - I do just that to 'talk' with my laptop :)

    Use the XP Network Setup Wizard - on the first page that says 'Select the statement that best describes your computer' check 'Other' > next. On the next page select the first option ' This computer .... connects directly to the Internet ..... Other computers .... also connect directly .....' and go on from there.
     
  6. 2004/07/22
    Omega

    Omega Inactive Thread Starter

    Joined:
    2004/03/11
    Messages:
    46
    Likes Received:
    0
    I will try that and see how it works out....I shall let you know

    THANX.....
     
  7. 2004/07/22
    24jedi Lifetime Subscription

    24jedi Well-Known Member

    Joined:
    2002/06/19
    Messages:
    186
    Likes Received:
    0
    If you can avoid the wizard's, that would be my advice. Also try to tackle one issue at a time.

    1. Get your LAN connectivity first.
    Put both PC's in the same workgroup.
    Use Static IP's 192.168.1.5 & 192.168.1.6
    Subnet Mask 255.255.255.0
    Defautl Gateway 192.168.1.1
    Test the connectivity by ping'n each workstation
    From Host-A to Host-B
    c:\ping 192.168.1.6
    From Host-B to Host-A
    c:\ping 192.168.1.5
    If you receive alot of info...this is good.
    If you receive request time out, this is a connectivity issue
    Make sure Network neighborhood is working as well.

    2. Now that both workstation can see each other, setup the modems.
    Install both modems and test dial-out capabilities using phone dialer in the accessories\communications from start menu.
    With both modems working make an ISP connection for each PC in network and dial-up connections.
    Next open IE and goto tools\interenet options\connections and select the profile for the ISP connection created in network ans dial-up connections.
    Make this the default. "always dial my default conmnection ".

    Once this is set, when you click on IE for a given PC, it should automatically start the modem connection to your ISP on that specific PC.

    Hope this helps
     
Thread Status:
Not open for further replies.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.